Skip to content

Beacons (NCDXF/IARU) from 1.62 ​

Is 15 m open towards Japan? Instead of waiting for a forecast, listen: the International Beacon Project run by the NCDXF and the IARU operates 18 beacons around the world that transmit around the clock on a fixed schedule on five bands. The Beacons (NCDXF) module in the sidebar shows you who is transmitting where — and can tune your transceiver to match via CAT.

How the beacons transmit ​

  • Frequencies: 14.100 · 18.110 · 21.150 · 24.930 · 28.200 MHz (CW).
  • Sequence: each beacon transmits for 10 seconds: its callsign at 22 wpm with 100 W, then four 1-second dashes at 100 W, 10 W, 1 W and 0.1 W. It then moves up one band, and the next beacon in the list starts.
  • Cycle: on every band you hear each beacon once every 3 minutes. The cycle starts every day at 00:00:00 UTC with 4U1UN on 14.100 MHz.

If you can still hear the 0.1 W dash, the path is excellent; if only the callsign comes through, the band is barely open.

On the air now ​

Five cards, one per band: callsign, location, distance and bearing from your QTH. The UTC clock runs at the top right, with a bar below it counting down to the next change (every 10 seconds). Clicking a card highlights the beacon on the map.

Set the clock

The schedule is accurate to the second. If your Mac's clock is off, the display won't match what you hear — the system time should be set automatically (System Settings → General → Date & Time).

Map ​

The world map shows all 18 beacons. The five currently transmitting are marked in their band colour and connected to your QTH by a great circle (short path); the selected beacon is drawn thicker. The dashed orange line is the day/night boundary — paths along the twilight zone often work particularly well.

Schedule of all beacons ​

The table lists all beacons with location, locator, distance and bearing. For each band it shows “now” or the UTC time at which the next transmission starts — for example when ZL6B will next come up on 20 m. Clicking a row shows that beacon's path on the map.

Operating status ​

Beacons go off the air from time to time. The NCDXF maintains a status list; HAM-Tools shows the imported status with its date below the table. Beacons listed as off the air carry a red QRT badge and appear as a red ring on the map. The tooltip shows the NCDXF note. The status may be out of date — if you hear a “QRT” beacon anyway, the NCDXF welcomes a report (ncdxf.org/beacon).

Location ​

Distance and bearing are calculated from the locator of the active log (e.g. an outdoor activation), otherwise from the locator in Settings → Station. Without a valid locator, distance, bearing and paths are missing.

Offline ​

The module needs no internet: the schedule is fixed and calculated from UTC time, and locations and status are built into the app.

Beacons via CAT ​

On the left, as in the other modules, is the CAT panel with frequency, S-meter and controls. Below it you control the transceiver for the beacons:

  • Follow Beacon — select a beacon in the table or under “On the Air Now”, then click. The rig goes straight to the band of the beacon's next transmission and waits there; the status box counts down until it comes up. It then jumps from band to band with the beacon (20 → 17 → 15 → 12 → 10 m, 10 seconds each) and returns to 20 m to wait for the next cycle. Within 50 seconds you hear on which bands, say, ZL6B reaches you. Selecting another beacon while following switches the target.
  • Hold Band — choose a band and click: the rig tunes once to the beacon frequency and stays there. Every 10 seconds the next beacon comes up; the table shows which one.
  • Stop (or Esc) — ends both. The rig returns to the frequency and mode it had at the start.

For safety: the rig switches to CW. There is no band change while PTT is pressed. If you turn the VFO yourself, following ends, and stopping will not overwrite your new frequency. Leaving the module or closing the window also ends following.

With the IC-7300 and others

This works with any rig HAM-Tools controls via CAT. The antenna should be usable on 20–10 m; a tuner that has to retune on every band change will swallow the start of the transmission.

HAM-Tools © HB9HJI · Funkwelt