Radio Settings
For CAT to run reliably, three places have to agree: the menu on the radio, the settings in HAM-Tools (Settings → CAT) and the cable or connection path. This page collects what we have tested with HAM-Tools on real radios.
Tested or just a profile?
Tested means we have run the radio with HAM-Tools ourselves (or a tester known to us by name has) — with date and firmware where known. All other radios have a profile with Hamlib defaults but no hands-on experience. If you run one of them successfully, let us know — we are happy to add your settings.
Checklist for every radio
- Fix the baud rate — the same value on the radio and in HAM-Tools. "Auto" often works on Icom, but it is the most common cause of sporadic drop-outs.
- CI-V address (Icom, Xiegu): the value in HAM-Tools must match the address in the radio menu. Notation:
0x94in the app =94hin the menu. - Right port: with several radios on the Mac, the port picker shows the USB serial number. If HAM-Tools reads a frequency that does not fit the radio (e.g. 14 MHz on an IC-9700), the wrong radio is on that port — the app warns you.
- No second program on the port: WSJT-X, fldigi & Co. share the radio through HAM-Tools (CAT Sharing), not through their own access to the same USB port.
- Copied a configuration? If you reuse an existing config with "Save as…" for another radio, the CI-V address comes along. After changing the model, click "Default" next to the CI-V address and save.
- Flow control on Icom: HAM-Tools always starts rigctld without handshake for Icom radios — a setting of "Hardware (RTS/CTS)" does no harm, it is ignored.
Overview
| Radio | Path | Baud | Format | CI-V | Status |
|---|---|---|---|---|---|
| Icom IC-7300 | USB | 19200 | 8N1 | 0x94 | tested |
| Icom IC-7610 | USB | 115200 | 8N1 | 0x98 | tested |
| Icom IC-9700 | USB | 115200 | 8N1 | 0xA2 | tested |
| Icom IC-705 | USB / WLAN | 115200 | 8N1 | 0xA4 | tested |
| Yaesu FTDX-10 | USB | 38400 | 8N1 | – | tested |
| Yaesu FTDX-101MP | USB | 38400 | 8N1 | – | tested |
| Yaesu FTX-1 | USB | 38400 | 8N1 | – | tested |
| Xiegu G90 | USB | 19200 | 8N1 | 0x70 | tested |
| Kenwood TS-480HX | USB | 9600 | 8N1 | – | tested (profile TS-590S) |
| FlexRadio 6000/8000 | LAN | – | – | – | tested (Flex-6300) |
All other profiles in HAM-Tools (among them IC-7100, IC-7600, FT-991A, FT-710, FTDX-101D, TS-2000, KX2/KX3, X6100, and the TS-480 and TS-590S profiles for their own radios) come preset with the Hamlib defaults but are not tested by us.
Icom
IC-7300
- HAM-Tools: profile "Icom IC-7300" (Hamlib 3073), 19200 baud, 8N1, handshake None, CI-V
0x94. - On the radio: Menu → SET → Connectors → CI-V → CI-V Baud Rate
19200(not "Auto"), CI-V Address94h. - Also tested: 115200 baud — then set 115200 on the radio as well. All that matters is that both sides use the same value.
IC-7610
- HAM-Tools: profile "Icom IC-7610" (Hamlib 3078), 115200 baud, 8N1, handshake None, CI-V
0x98. - On the radio: Menu → SET → Connectors → CI-V — CI-V USB Baud Rate and CI-V Address set to the same values as in HAM-Tools (not "Auto").
- Quirk: antenna selection (ANT1/ANT2) via CAT is currently disabled in HAM-Tools because reading the antenna disturbed the connection. All other functions work.
- Port: the built-in USB chip (Silicon Labs CP210x) shows up as
usbserial-…. With an IC-9700 on the same Mac, tell the ports apart by the serial number in the port picker.
IC-9700
- HAM-Tools: profile "Icom IC-9700" (Hamlib 3081), 115200 baud, 8N1, handshake None, CI-V
0xA2. - On the radio: Menu → SET → Connectors → CI-V — CI-V USB Baud Rate and CI-V Address set to the same values as in HAM-Tools (not "Auto").
- Typical symptom of swapped ports: HAM-Tools reads an HF frequency and the mode read times out — then another radio is on the selected port.
IC-705
- USB: profile "Icom IC-705" (Hamlib 3085), 115200 baud, 8N1, CI-V
0xA4. On the radio: Menu → SET → Connectors → CI-V — CI-V USB Baud Rate and CI-V Address as in HAM-Tools (not "Auto"). - WLAN: no cable and no extra software — step by step in the IC-705 over WLAN tutorial.
- WLAN quirk: the IC-705 allows exactly one network session. After a crash or a hard quit of the app it stays occupied until the radio releases it after a few seconds or is restarted.
Yaesu
FTDX-10
- HAM-Tools: profile "Yaesu FTDX-10" (Hamlib 1042), 38400 baud, 8N1, handshake None.
- On the radio: FUNC → Operation Setting → General: CAT RATE
38400bps, CAT TIME OUT TIMER100msec, CAT RTSON. - Tested: November 2026 (HB9HJL), USB cable straight into the radio.
- Port: the built-in USB chip (Silicon Labs CP210x) presents two ports — CAT runs on the "Enhanced Port".
FTDX-101MP
- HAM-Tools: profile "Yaesu FTDX-101MP" (Hamlib 1044), 38400 baud, 8N1, handshake None.
- On the radio: FUNC → Operation Setting → General: CAT RATE
38400bps, CAT TIME OUT TIMER10msec, CAT RTSON. The timer is not critical — the same setup ran with 100 ms on the FTDX-10. - Tested: November 2026 (HB9HJL), USB cable straight into the radio.
- Port: as with the FTDX-10, pick the CP210x "Enhanced Port".
- Audio: with two receivers (MAIN/SUB) the receive audio may sit on the right channel — for SSTV HAM-Tools picks the louder channel automatically.
FTX-1
- HAM-Tools: profile "Yaesu FTX-1" (Hamlib 1051), 38400 baud, 8N1, handshake None.
- Tested: continuously on our own radio (2026) — CAT, PTT, tuner, audio and repeater/memory functions down to the details.
- On the radio: CAT rate 38400 — the same value as in HAM-Tools. For digital modes set Radio Settings → Mode DATA to
USB. - Tuner: the Tune button starts the tuner with the FTX-1's own command (
AC103;), not the one otherwise used on Yaesu. - Audio: shows up as "USB Audio Device"; receive audio on channel 1 (left).
- Quirk: the display sometimes lags behind CAT changes.
Kenwood
TS-480HX
- Tested with the profile "Kenwood TS-590S" (Hamlib 2031), 9600 baud, 8N1, flow control Hardware (RTS/CTS). We have not yet tried the dedicated "TS-480" profile (Hamlib 2028).
- Unlike with Icom, HAM-Tools passes the flow-control setting on to rigctld for Kenwood.
- On the radio: baud rate 9600 — the same value as in HAM-Tools.
Xiegu
G90
- HAM-Tools: profile "Xiegu G90" (Hamlib 3088), 19200 baud, 8N1, handshake None, CI-V
0x70. - Tested: November 2026, firmware V1.79 (BASE and APP), USB cable on the G90's serial port (shows up as "USB <-> Serial").
- On the radio: nothing to set — CAT is always active on the G90, address
70hand 19200 baud are fixed. In HAM-Tools the profile values (above) are all you need; if the CI-V address shows anything else, click "Default (0x70)" and save. - Quirk: the first mode query after start-up takes the G90 about 4–5 seconds; after that it answers immediately. HAM-Tools waits for it when connecting . Older versions dropped the connection shortly after start-up.
FlexRadio
6000/8000 Series
- HAM-Tools: profile "FlexRadio 6000/8000 Series – Slice A" (through D), connection via the radio's IP address on the LAN, no USB port.
- Tested: Flex-6300 (October 2026), alongside SmartSDR for Mac.
- Audio: via DAX.
Something missing or wrong?
If your radio is missing here or you need different values: report it with radio, firmware, connection path and the settings that work for you.